Teledyne Installation Guide Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 62

background image

CombiFlash® R

f

Installation Guide

4-4

4. Click OK to save the settings. The Combi

Flash

R

f

system

will send a test page to the printer.

After successfully printing a test page, the network printer
will be available for printing using the File>Print menu
command or through the

Automatically Print Report at End of

Run

feature described below.

4.1.3 Automatically Print Report at End of Run

If the Combi

Flash

R

f

system can successfully print to a

network printer (Section 4.1.2), it may be configured to print a
report at the end of each run. The report includes the method
settings, chromatogram, and peak/tube collection information.
To enable this feature:

1. Select the Tools>Configuration menu command.

2. The Configuration window has two tabs. Select the

Instrument Configuration tab.

3. Select the “Automatically Print Report at End of Run”

option.

4. Click OK to save the setting.

4.2 Direct Connection

A direct connection supports communication between the
Combi

Flash

R

f

system and a single PC that meets the

recommendations in Table 4-1.

This guide provides instructions for Windows 2000 (section
4.2.1), Windows XP (4.2.2), and Windows Vista (4.2.3). Refer to
the applicable section, then follow the instructions in section
4.2.4 to complete the direct connection.

Note

A direct connection requires a “crossover” CAT5 cable. Standard
CAT5 network cables will not work. You can purchase a crossover
cable locally or ask your Information Technology department to
assemble one. You can also order a crossover cable (part number
480-6545-02) from Teledyne Isco.

Note

These instructions assume that the system is using the factory-set
IP address of 192.168.1.51.

«
...
41
42
43
44
45
...
»

Содержание Installation Guide































































Отзывы:

Нет отзывов

Похожие инструкции для Installation Guide

Бренд: Eagle Страницы: 3

Бренд: NEC Страницы: 54

Бренд: Banfer Страницы: 6

Бренд: Nitecore Страницы: 4

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: Idex Страницы: 141

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

LED Street Bar 16x3W RGB IP65

Бренд: Varytec Страницы: 9

Бренд: VARILITE Страницы: 8

EVENTPROFILE VL800

Бренд: Vari Lite Страницы: 34

Optica 30 Series

Бренд: Varex Imaging Страницы: 36

Бренд: L-Acoustics Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды