Teledyne Installation Guide Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 62

background image

Section 2 System Preparation

2-5

The Solvent Level Sensing air line connects to the back panel
with a compression fitting. This fitting must be airtight. To
connect tubing using the compression fittings:

1. Slide the nut and ferrule onto the tubing as shown in

Figure 2-1 or 2-2.

2. Fully insert the tubing into the threaded bulkhead fitting

on the back panel of the system.

3. Finger-tighten the nut onto the threaded bulkhead fitting.

This will seat the ferrule in the fitting.

Note

When using higher-density solvents such as dichloromethane
(DCM), place the solvent container level with or above the
CombiFlash Rf system. Placing solvent containers below the level
of the Rf can contribute to decreased flow due to the high vapor
pressure of DCM. This problem becomes more pronounced as the
ambient temperature increases.

2.5 Connect Waste Lines

WARNING

Risk of fire or equipment damage. Failure to connect Waste
Port tubing may allow organic solvents to pool in unsafe areas,
possibly creating dangerous levels of flammable vapors.

WARNING

Risk of fire ignited by electrostatic discharges. Never
substitute the black tubing on CombiFlash systems. The black
PTFE tubing (P/N 023-0503-06) is conductive. This tubing is
required to dissipate static electricity.

CAUTION

Elevated flammable vapor levels are possible. Ensure that the
waste container is adequately ventilated, preferably by placing it in
a fume hood.

The system has two waste outlets on the back panel: Diverter
Valve waste and Inject Valve waste. You can route waste to a
common collection container, or to individual containers.

«
...
17
18
19
20
21
...
»

Содержание Installation Guide































































Отзывы:

Нет отзывов

Похожие инструкции для Installation Guide

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

DependaBar DB-18-PCW

Бренд: Healthcraft Страницы: 13

Бренд: Turner Designs Страницы: 55

Бренд: IN Страницы: 6

Бренд: Selecta Страницы: 20

Бренд: IKA Страницы: 36

MEGA STROBE/DMX

Бренд: American DJ Страницы: 2

Бренд: Bauerfeind Страницы: 14

Бренд: R.V.R. Elettronica Страницы: 38

Бренд: Studio Technologies Страницы: 23

Бренд: Gardena Страницы: 9

NTRW39121-INT.0

Бренд: NordicTrack Страницы: 28

U-Trough Power Sweep

Бренд: Sukup Страницы: 44

Бренд: Vistosi Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды