Teledyne Installation Guide Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 62

background image

Section 1 Introduction

1-3

1.3 Operating Overview

The Combi

Flash

R

f

may be controlled through its built-in

touch screen panel or by a Windows computer running
Microsoft Internet Explorer 6 or newer.

The Combi

Flash

R

f

is equipped with the touch screen display

for local control. For Windows computer control, the
Combi

Flash

R

f

may be controlled by the computer in two

different ways using TCP/IP protocol—direct or network. A
direct connection uses a cross-over cable between Ethernet
ports on the Combi

Flash

R

f

and computer. A network

connection allows control from a computer on an established
network.

Note

Teledyne Isco recommends that you obtain assistance from your
Information Technology department before attempting direct or
network connections to a Windows computer.

1.3.1 Multiple Control Possibilities

The system can be accessed from the built-in touch panel and
up to ten network computers. The touch panel shares control
with all connected computers. The system performs the most
recent command from any control input.

1.3.2 File Storage

To support operation from a variety of direct and network
connections, the software and all files are stored in the
Combi

Flash

R

f

on an internal hard drive. This ensures that

your compound purification methods and run history files can
be viewed from any connection.

«
...
4
5
6
7
8
...
»

Содержание Installation Guide































































Отзывы:

Нет отзывов

Похожие инструкции для Installation Guide

Бренд: ParaBody Страницы: 4

Бренд: XAG Страницы: 24

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: AAON Страницы: 36

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FASTERHOLT Страницы: 96

Бренд: MagCore Страницы: 80

Бренд: MagCore Страницы: 80

Бренд: UniPix Страницы: 24

Бренд: JBL Страницы: 17

Бренд: Jäger Страницы: 36

Бренд: IMG STAGE LINE Страницы: 12

Бренд: Grundfos Страницы: 43

KEW FORK 2300 R

Бренд: KYORITSU Страницы: 9

Бренд: Thinkrider Страницы: 24

Бренд: K-Tech Страницы: 2

Бренд: EarthMark Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды