Tektronix TLA7000 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 121

background image

Preface

This manual contains information needed to install your Tektronix logic analyzer
and related accessories.

To prevent personal injury or damage consider the following requirements before
attempting service:

The procedures in this manual should be performed only by quali

fi

ed service

personnel.

Read the General Safety Summary and Service Safety Summary found at
the beginning of this manual.

Be sure to follow all warnings, cautions, and notes in this manual.

TLA7000 Series Logic Analyzers

The TLA7000 Series Logic Analyzers are comprised of a 2-module portable
mainframe (TLA7012), and a 6-module benchtop mainframe (TLA7016).

The TL708EX TekLink 8-Port Hub) and a local area network (LAN) gigabit
(Gb) switch expand the system and connect it to your network. A dedicated PC
controller (TLA7PC1) is also available, or you can load the application software
on your PC.

The logic analyzers are built upon the Microsoft Windows operating system
which allows you to install PC-compatible, third-party hardware and software
on the instrument.

The user interface operates under the Microsoft © Windows operating system.
Microsoft recommends the following to ensure your instrument is protected:

Use an internet

fi

rewall.

Install operating system updates regularly.

Use up-to-date antivirus software.

Table i: Windows Software Support Matrix

Ships with WinXP
pre-installed

1

Field upgrade to
WinXP

2

Run TLA V5.1 on
Windows 2000

TLA7012
TLA7PC1

3

Yes

N/A

N/A

TLA5000

Yes

Yes

Yes

1

WinXP is pre-activated. No activation is required when you

fi

rst receive your instrument. Activation may be

required if you restore the hard disk image from the CD.

2

The WinXP upgrade is done via the Hard Disk Image supplied by Tektronix. There are different Hard Disk Images

supplied, depending on your motherboard. After the upgrade, you will need to activate WinXP.

3

The TLA7PC1 is a PC controller that is sold by Tektronix for use with the TLA7016 benchtop mainframe.

TLA7000 Series Logic Analyzers Installation Manual

xi

«
...
13
14
15
16
17
...
»

Содержание TLA7000 Series


























































































































Отзывы:

Нет отзывов

Похожие инструкции для TLA7000 Series

Бренд: TaiDoc Страницы: 31

Бренд: Campbell Страницы: 22

Бренд: Campbell Страницы: 32

Бренд: Campbell Страницы: 40

CR3000 Micrologger

Бренд: Campbell Страницы: 12

Бренд: R.M. Young Страницы: 8

Бренд: Campbell Страницы: 21

Бренд: DAKOTA ULTRASONICS Страницы: 25

Бренд: DAKOTA ULTRASONICS Страницы: 36

Бренд: ECO Sensors Страницы: 22

Бренд: ECO Sensors Страницы: 7

Бренд: F&F Страницы: 24

Бренд: Unico Страницы: 96

Бренд: Technoline Страницы: 1

Бренд: Environmental Express Страницы: 40

Smart Air Quality Monitor

Бренд: Lennox Страницы: 28

Бренд: Roland Страницы: 96

Бренд: NCS Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды