manualshive.com logo in svg

Tektronix TLA7000 Series, Руководство по установке

Поделиться
Скачать
Tektronix TLA7000 Series Скачать руководство пользователя страница 75

Merging Modules

TLA7PG2 Pattern Generator Module Merging Rules

The following pattern generator module merging rules must be followed:

Pattern generator modules are merged through software.

Pattern generator modules must be physically adjacent.

Pattern generator modules may not be merged across mainframes.

Merging pattern generator modules with unequal memory depths will result in
the merged set assuming the depth of the shallowest pattern generator module.

Pattern generator modules must have the same

fi

rmware version.

When merged, the left-most pattern generator module is the master.

Merge Procedure

Complete the following steps to create a merged module from two or more
individual modules. You must complete these steps prior to installing the modules
in a mainframe.

CAUTION.

To avoid damaging the mainframe or any modules, always power off

the mainframe before removing or installing modules.

1.

Determine which modules will reside in the highest-numbered slots in a
single mainframe.

2.

Place the merge connector of these modules in the extended position. The
module in the lowest-numbered slot must have the merge connector in the
recessed position.

The following

fi

gure shows an example for determining the location of the

master module with the merged module set. (See Figure 48.) Even though the

fi

gure shows a

fi

ve module set, you can still use the it to position the master

module with respect to the slave module. If you have a two module set, the master
module is located in the lower-numbered slot, and the slave module is in the
higher-numbered slot.

TLA7000 Series Logic Analyzers Installation Manual

57

Содержание TLA7000 Series


























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды