Tektronix RSA5100B series, Техническое описание

Страница: 28 / 153

Specifications
Table 10: Noise and distortion 1 (cont.)
Characteristic Description
Preamp ON (Opt. 50/51)
Speci fi cation
Typical
1 MHz to
32 MHz, LF
Band –158 dBm/Hz
(RSA5103B/5106B) –160 dBm/Hz
(RSA5103B/5106B)
1 MHz to
10 MHz –158 dBm/Hz –160 dBm/Hz
10 MHz to
2 GHz –164 dBm/Hz –167 dBm/Hz
2 GHz to
3 GHz –163 dBm/Hz –165 dBm/Hz
3 GHz to
6.2 GHz –162 dBm/Hz
(RSA5106B) –164 dBm/Hz (RSA5106B)
3 GHz to
4 GHz –160 dBm/Hz
(RSA5115B/5126B) –163 dBm/Hz
(RSA5115B/5126B)
4 GHz to
6.2 GHz –159 dBm/Hz
(RSA5115B/5126B) –162 dBm/Hz
(RSA5115B/5126B)
6.2 GHz to
13 GHz –159 dBm/Hz
(RSA5115B/5126B) –162 dBm/Hz
(RSA5115B/5126B)
13 GHz to
23 GHz –157 dBm/Hz
(RSA5115B/5126B) –160 dBm/Hz
(RSA5115B/5126B)
23 GHz to
26.5 GHz –153 dBm/Hz
(RSA5126B) –156 dBm/Hz (RSA5126B)
1
All noise and distortion measurements are made with Preamp OFF except where noted.
2 Maximize Dynamic Range, “RF & IF Optimization” Mode, Span: 5 MHz.
3 The 1 dB compression point for the RF conversion system cannot be measured from outside the instrument, nor can signals get near it in operation. This is
because the A/D converter will clip before the 1 dB compression is reached.
4
Each signal level –25 dBm at the RF input. 1 MHz tone separation. Attenuator = 0, Ref Level = –20 dBm.
5
Each signal level –50 dBm at the RF input. 1 MHz tone separation. Attenuator = 0, Ref Level = –45 dBm.
Table 11: Channel Response – Amplitude & Phase Flatness (Standard/Option B40)
for RSA5103B/5106B:
Frequency range
Span Amplitude fl atness Phase fl atness
Speci fi cation Typical, RMS Typical, RMS
0.01 GHz to 6.2 GHz ≤ 300 kHz 1 ±0.10 dB 0.05 dB 0.1°
0.03 GHz to 6.2 GHz ≤ 25 MHz ±0.30 dB 0.20 dB 0.5°
0.03 GHz to 6.2 GHz ≤ 40 MHz 2 ±0.30 dB 0.20 dB 0.5°
0.07 GHz to 3.0 GHz ≤ 85 MHz 3 ±0.50 dB 0.30 dB 1.5°
>3.0 GHz to 6.2 GHz ≤ 85 MHz 3 ±0.50 dB 0.40 dB 1.5°
0.1 GHz to 6.2 GHz ≤ 165 MHz 4 ±0.50 dB 0.40 dB 1.5°
0.001 GHz to 0.032 GHz
(LF band) ≤ 20 MHz ±0.40 dB 0.30 dB 0.5°
14 RSA5100B Series Technical Reference