Tektronix RSA5100B series Скачать руководство пользователя страница 88

Страница: 88 / 153

Performance Veriﬁcation

Touch Screen Check

Check that the touch screen detects touches:

Verify that the touch screen is enabled (

Touch Screen Off

button is not

lighted).

Use your ﬁnger or a stylus to touch several of the on-screen touchable
readouts, such as RBW or Span, and verify they become active when touched.

Diagnostics

Run a complete Diagnostics test session:

Select

Tools > Diagnostics

from the menubar.

Select the

All Modules, All Tests

checkbox at the top of the list.

Touch the

RUN

button. The diagnostics tests will take some time to complete,

and some of them are interactive:

Noise Source Drive 28VDC Out diagnostic will ask you to test the noise
source output on the RSA5100B rear-panel.

Check with a voltmeter that the voltage is 28 V ±2 V.

The LED Check diagnostic will ask you to verify that all the highlighted
LEDs are turned on:

Compare the LEDs highlighted in the diagnostic display with the

buttons on the front panel.

Press each of the keys and rotate the knob on the front panel. You

should see the corresponding key in the diagnostic display turn green.
Verify that each key is recognized.

Click the PASS or FAIL button when done.

The Display Pixel Test will ask you to look for video problems on the
test patterns:

Check the Green screen for any stuck or missing pixels. Any keypress,

click, or touch will move to the next screen.

Repeat with the Red screen, the Blue Screen, and the Gray scale

screen. Select Yes or No when the LCD Test dialog asks “Did you
see any video problems”.

When all diagnostics tests have completed, check that there is a check mark
beside each diagnostic name. An X instead of a check mark indicates that
the diagnostic had a failure.

Click the

Diagnostics Failure

Info tab and verify there is no failure

information listed.

Click the

Exit Diagnostics

button to exit diagnostics.

RSA5100B Series Technical Reference

Содержание RSA5100B series


























































































































































Результаты поиска

Содержание RSA5100B series

Отзывы:

Tektronix RSA5100B series, Техническое описание, Страница: 88 / 153

Результаты поиска

Содержание RSA5100B series

Отзывы: