TekTone Tek-CARE 550 Скачать руководство пользователя страница 45

Страница: 45 / 51

System Customization

9. When all updates have been made, select

File>Commit Configuration to System.

Assign Check-In Times to Check-In Transmitters

In this step, check-in times created during system setup will be assigned to their

corresponding check-in transmitters.
Check-In times must be assigned in the Event Monitor software.

Assign Check-In Times to Transmitters

1. In the Event Monitor software, click the

Registers

button, and then chose

Transmitters

from the page selection pane.

2. Click on the

Dev#

of a check-in transmitter in the list at the left. Refer to your

completed programming worksheet to determine which resident’s room the

transmitter is located in. (

SF559 Two Button Pull-Cord Stations

programmed

with a

Check-In

button membrane insert are used as check-in devices.)

3. Click on the

Check In

tab in the

Transmitters–Details

area. This tab is only

available for transmitters that have been configured as check-in devices.

4. Click on the

Edit

button in the

Transmitters–Details

area, select one or more

Check-In Times

, and click the

Apply

button. Assign just one check-in time per

day to a transmitter,

although one check-in time may be assigned for weekdays

and another for weekends. The available check-in times are dependent on shifts

IL948 Tek-CARE

500 & Tek-CARE

550 Installation Manual • 37

Содержание Tek-CARE 550

















































Результаты поиска

Содержание Tek-CARE 550

Отзывы:

Бренды по названию

Популярные бренды

TekTone Tek-CARE 550, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Tek-CARE 550

Отзывы:

Бренды по названию

Популярные бренды