TekTone Tek-CARE 550 Скачать руководство пользователя страница 13

Страница: 13 / 51

System Installation and Setup

SF525ES and SF525/2ES NO/NC Universal Contact Transmitters:

The SF525ES

and SF525/2ES transmitters are used with any standard NO or NC switch, enabling

the Tek-CARE

500 system to monitor a variety of inputs. The SF525ES includes one

selectable NO/NC inputs and the SF525/2E includes one selectable NO/NC input plus

an NC-only input. The secondary NC-only input’s call type has not been preassigned.

The call type must be assigned using the Hardware page in the Config Tool software.

Alarms are automatically reset when returned to a normal state or when calls are reset

at the Tek-BRIDGE™ depending on system programming.

SF527ES Wireless Support Module:

The SF527ES Wireless Support Module may be

connected to an SF337C Waterproof Switch or SF339 Pushbutton Emergency Switch

to allow these switches to operate as wireless devices. This is especially useful in an

environment such as a shower or bathroom where calls must be easily placed and

water resistance is desired.

SF529ES Resident Check-In/Assistance Call Station:

The Wireless Resident Check-In

and Assistance Station is used when both a high-priority call and resident check-in is

desired. High priority calls must be reset at the point of origin.The SF529ES Resident

Check-In/Assistance Call Station includes a plastic pull cord kit.

SF530ES Room Station:

The Room Station transmitter is used where use of call cords

are desired. Alarms must be reset at the point of origin. The SF530ES Room Station

provides a standard 1/4” call cord receptacle and a reset pushbutton. The device also

includes cord-out detection, annunciated at the Tek-BRIDGE™.

SF531ES Emergency Switch:

The SF531 Emergency Switch is used where a high

priority call is desired, but water resistance is not required. The SF531ES Emergency

Switch includes a plastic pull-cord kit. Alarms placed from the transmitter must be

reset at the point of origin.

SF505ES Smoke Detector:

The SF505ES Smoke Detector transmits an alarm signal

when the smoke detector is activated. The signal will reset automatically when the

detector is clear of all smoke.

SF515ES Motion Detector:

The SF515ES Passive Infra-Red Motion Detector is sensitive

to moving heat sources. It can be used as a check-in device or as a security device on

the Tek-CARE

500 system.

IL948 Tek-CARE

500 & Tek-CARE

550 Installation Manual • 5

Содержание Tek-CARE 550

















































Результаты поиска

Содержание Tek-CARE 550

Отзывы:

Бренды по названию

Популярные бренды

TekTone Tek-CARE 550, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Tek-CARE 550

Отзывы:

Бренды по названию

Популярные бренды