TekTone Tek-CARE 550 Скачать руководство пользователя страница 25

Страница: 25 / 51

System Installation and Setup

from System

to update the configuration in the Config Tool.

Select

File>Save Configuration

to save your programming changes.

Adding Tek-CARE

550 Transmitters with the Config Tool

In certain cases, adding transmitters manually through the Config Tool is preferable to

adding them automatically in the Event Monitor. These situations may include when

two independent Tek-CARE

550 systems are located in close proximity to each other

or if a small number of devices need to be added to an existing system. The Config Tool

method requires that certain information about the transmitters be entered manually.

1. With the Event Monitor software running, open the

Config Tool

software and

choose the appropriate network interface. On the right side of the Config Tool

splash screen, choose

Load Configuration from System

to ensure that the most

current configuration will be edited.

2. Select

Transmitters

in the page selection pane.

3. Click the

Add

button in the

Transmitters

pane. This unlocks the

Details

pane

for editing.

4. In the

Details

pane, select

TC550

from the

Transmitter Family

drop-down box

to add Tek-CARE

550 transmitters.

5. Choose a four digit

Device Number (Dev#)

to be assigned to the device to be

added and type it into the box.

6. Open the case of the device to be added. Find the eight digit long address sticker

located on the circuit board and copy it into the

Long Address

field in the

Details

pane. Add four zeroes to the beginning of the long address. The

7. If the device will be used immediately, ensure that the

In Use

box is checked.

If the device is to be placed in reserve, but not to be enabled until a later time,

leave this box unchecked. Before placing the device in reserve or storage, remove

the battery from the device.

8. Select the appropriate device type from the

Hardware

drop-down menu. If

adding an

SF559 Two-Button Pull Cord Station

, choose the entry from the

Used As:

drop down menu that matches the button insert placed in the device.

9. If the transmitter will be powered by a plug-in power supply, be sure and check

the

Line Powered

box.

10. If the device is being added to an existing system, choose the appropriate

location (if any) from the

Location

drop-down menu in the

Assignment

pane.

If the device is being added to a new system, select

Nowhere

as the location.

Locations will be added later.

Select

File>Save Configuration

to save your programming changes, then select

File>Commit Configuration to System

to update the Tek-Care

system.

Add Facility Maps and Locations

The Tek-CARE

system has the option to store maps of the care facility it is installed

in. These maps can be used to view transmitter locations and, when adding resident

information, associate a particular transmitter with a room, and thus an individual

resident entry.
Locations are where transmitters are physically installed throughout the facility.

Locations must be defined whether or not facility maps are used. Each stationary

IL948 Tek-CARE

500 & Tek-CARE

550 Installation Manual • 17

Содержание Tek-CARE 550

















































Результаты поиска

Содержание Tek-CARE 550

Отзывы:

Бренды по названию

Популярные бренды

TekTone Tek-CARE 550, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Tek-CARE 550

Отзывы:

Бренды по названию

Популярные бренды