background image

409-10204 

Rev G 

15 

of 23 

5.2.

 

Lubrication 

The moving parts of the machine require regular lubrication to ensure reliable service and long life. The 
preferred greases are Chevron Ultra-Duty EP NLGI 2, Chevron Ulti-Plex EP NLGI 2, and Caltex Ultra-Duty EP 
NLGI 2. 

NOTE 

Contact TE engineering for 2

nd

 choice alternates. 

CAUTION 

It is important to only use Lithium-based grease with extreme pressure (EP) additives. 
 

NOTE 

For operation in temperatures below 10° C [50° F], it will be necessary to use a No. 1 grease. 

Using a grease gun, apply grease every 250,000 cycles to the fittings at the following locations and as shown 
in Figure 10: 

 

the left side of the ram assembly; 

 

the right side of the ram assembly; 

 

the left side of the frame just behind the ram assembly at two places; and 

NOTE 

Give one pump of grease while the ram is near the top of its stroke and one pump of grease while the ram is near the bottom 
of its stroke for best distribution of grease around the bearing. 

 

the crimp height adjuster pivot pin. 

Figure 10 

6.

 

ADJUSTMENTS 

The following adjustments are necessary to maintain the machine in operating condition, and to set up the 
machine after replacing parts. 

Chevron, Caltex, and Lithium are trademarks of their respective owners. NLGI is the National Lubrication and Grease Institute. 

DANGER 

To avoid personal injury, ALWAYS disconnect electrical and air supplies before performing adjustments. 

Lubrication Points

 

Lubrication Points

 

Содержание AMP 3K/40
























Отзывы: