Taylor 811 series Скачать руководство пользователя страница 49

Страница: 49 / 58

TROUBLESHOOTING GUIDE

7-5

Model 811, 813, 819, 821 Series

Troubleshooting Guide

Gas Zones Only

Problem

Probable Cause

Remedy

1. The display reads



IGNITION TERMINATED
XX. CHECK IF GAS



SUPPLY IS OK. IF
ERROR PERSISTS,
CALL SERVICE-GAS.

a. Controller may need to be reset, or there may be an

issue with the gas pressure.

a. Verify that the gas supply is turned

on and connected to the grill. Turn
the grill off and back on; then
select a menu item. If the problem
persists, call a service technician.

b. The pressure switch is faulty.

b. Call a service technician.

c. The blower is faulty.

c. Call a service technician.

2. The burner will not light.

The display reads
IGNITION FAILURE XX.
CHECK IF GAS SUPPLY
IS OK. IF ERROR
PERSISTS, CALL
SERVICE-GAS.

a. The quick disconnect gas hose is not fully engaged.

a. Re-engage the quick disconnect.

b. The manual shutoff valve is in the OFF position.

b. Turn the valve to the ON position.

c. Air is in the gas hose.

c. Wait 5 minutes before relighting.

d. The processor control is faulty.

d. Call a service technician.

e. The spark ignition module is faulty.

e. Call a service technician.

f. The gas solenoid is faulty.

f. Call a service technician.

g. The electrode is faulty.

g. Call a service technician.

h. The interface board is faulty.

h. Call a service technician.

3. The burner lights but will

not stay lit.

a. The electrode is faulty.

a. Call a service technician.

b. Improper ground.

b. Call a service technician.

4. The burner lights, but the

zone is cool or overheats.

a. The grill is out of calibration.

a. Call a service technician.

b. The processor control is faulty.

b. Call a service technician.

c. The thermocouple is faulty.

c. Call a service technician.

Zone ID's:

BR: Bottom Rear

TR: Top Rear

BM: Bottom Middle

TF: Top Front

BF: Bottom Front

Содержание 811 series



























































Результаты поиска

Содержание 811 series

Отзывы:

Бренды по названию

Популярные бренды

Taylor 811 series, Руководство оператора

Результаты поиска

Содержание 811 series

Отзывы:

Бренды по названию

Популярные бренды