Section 3
3-1
Model 811, 813, 819, 821 Series
Safety
3
Safety
We at Taylor Company are concerned about the safety of
the operator when he or she comes in contact with the
grill and its parts. Taylor has gone to extreme efforts to
design and manufacture built-in safety features to protect
both you and the service technician. As an example,
warning labels have been attached to the grill to further
point out safety precautions to the operator.
IMPORTANT!
Failure to adhere to the
following safety precautions may result in severe
personal injury. Failure to comply with these warnings
may damage the machine and its components.
Component damage will result in part replacement
expense and service repair expense.
To Operate Safely
NOTICE! DO NOT
operate the grill without
reading this operator's manual. This manual should be
kept in a safe place for future reference.
IMPORTANT!
This machine is to be used only
by trained personnel. It is not intended for use by children
or people with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the machine.
WARNING!
Failure to follow the instructions
below may result in severe injury or death from
electrocution:
•
DO NOT
operate the grill unless it is properly
grounded.
•
DO NOT
operate the grill with larger fuses than
specified on data label.
•
DO NOT
operate the grill unless all service
panels and access doors are attached with
screws.
•
All repairs must be performed by a Taylor
service technician.
•
The main power supplies to the grill must be
disconnected prior to performing any repairs.
•
Only Taylor service technicians or licensed
electricians may install a plug or replacement
cord on these machines.
•
Stationary machines which are not equipped
with a power cord and a plug or other device to
disconnect the machine from the power source
must have an all-pole disconnecting device with
a contact gap of at least 1/8 in. (3 mm) installed
in the external installation.
•
Machines that are permanently connected to
fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected
or not used for long periods, or during initial
installation, shall have protective devices such
as a GFI to protect against the leakage of
current installed by the authorized personnel to
the local codes.
•
Supply cords used with this machine shall be
oil-resistant, sheathed flexible cable not lighter
than ordinary polychloroprene or other
equivalent synthetic elastomersheathed cord,
(code designation 60245 IEC 57) installed with
the proper cord anchorage to relieve conductors
from strain, including twisting, at the terminals
and protect the insulation of the conductors from
abrasion.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent,
or similarly qualified person, to avoid a hazard.
!
!
Содержание 811 series
