manualshive.com logo in svg

Taylor 811 series, Руководство оператора

Поделиться
Скачать
Taylor 811 series Скачать руководство пользователя страница 13

SAFETY

3-3 

Model 811, 813, 819, 821 Series 

Safety 

3

CAUTION!

 For thorough cleaning, the grill 

must be pulled away from the wall. Before moving the 
grill, remove the grease cans. Turn off the gas at the 
quick connect shutoff valve on the flexible hose. 
Disconnect the gas quick connector. Disconnect the 
tether to the grill, located on the back panel of the unit.

To return the grill to its original position, reverse the 
steps. Use extreme caution to smoothly and slowly roll 
the grill backward into place.

Failure to do so may cause the grill to tip and can result in 
severe machine damage or personal injury.

NOTICE!

 Cleaning and sanitizing schedules 

are governed by your federal, state, or local regulatory 
agencies and must be followed accordingly. Please refer 
to the cleaning section of this manual for the proper 
procedure to clean this machine.

IMPORTANT!

 Access to the service area of 

the machine is restricted to persons having knowledge 
and practical experience with the machine, in particular 
as far as safety and hygiene are concerned.

IMPORTANT!

•

DO NOT 

obstruct the ventilation openings at the 

rear of this machine.

•

DO NOT 

obstruct the flow of air in and around 

the grill.

NOTICE! 

All warning labels that have been 

attached to the grill to further point out safety precautions 
to the operator.

This machine is made in America and has American 
sizes on hardware. All metric conversions are 
approximate and vary in size.

Noise Level: 

Airborne noise emission does not exceed 

70 dB(A) when measured at a distance of 3.3 ft. (1.0 m) 
from the surface of the machine and at a height of 5.25 ft. 
(1.6 m) from the floor.

These instructions are valid only if the country code 
symbol appears on the appliance. If the symbol does not 
appear on the appliance, refer to the technical 
instructions which give the necessary instructions for 
adapting the machine to the utilization conditions of that 
country.

!

!

!

!

Содержание 811 series



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды