Taylor 811 series Скачать руководство пользователя страница 47

Страница: 47 / 58

TROUBLESHOOTING GUIDE

7-3

Model 811, 813, 819, 821 Series

Troubleshooting Guide

12.The product is undercooked or

overcooked.

a. The release sheet is worn.

a. Replace the release sheet.

b. Incorrect cooking time.

b. Reset the processor control

for the correct time.

c. Incorrect temperature setting.

c. Adjust the processor control

to the proper setting.

d. The upper platen or lower grill surface is

not clean and/or has carbon buildup.

d. Follow closing procedures to

properly clean the upper
platen and the lower grill



surface and to remove
carbon buildup.

e. There is a grease or carbon buildup on the

bottom of the upper platen handles.

e. Follow closing procedures to

properly clean and remove
carbon buildup from the



bottom of the platen handles.

f. Product is out of specification.

f. Product must be within



specified tolerances



(thickness, shape, raw, or



frozen temperatures).

g. Product may have accumulated ice



crystals.

g. Ensure that open boxes are

kept closed and that all the
product is covered during
storage.

h. Cooking procedures may have been



followed incorrectly.

h. Ensure that the product was

removed immediately after
the cook cycle ended.



Double check that the



correct product was selected
from the Main Menu screen.

i. Other equipment may be at fault.

i. Check temperatures of all

meat storage freezers. Make
sure they are set to 0



(-18

C). Check temperatures

of all meat storage



refrigerators. Make sure they
are set to 38

F-42



C-5

C).

j. The preset gap height is incorrect.

j. Verify the product settings

(time, temperature, gap, etc.)
are programmed in the



controller correctly. Always
consult with the owner and
regional manager before
changing the control



settings. See guide for



programming instructions.

k. The heating zone is not heating.

k. Call a service technician.

13. The display reads PROBE OPEN and

displays the specific zone.

a. The thermocouple or the thermocouple

interface board is faulty.

a. Call a service technician.

Problem

Probable Cause

Remedy

Содержание 811 series



























































Результаты поиска

Содержание 811 series

Отзывы:

Бренды по названию

Популярные бренды

Taylor 811 series, Руководство оператора

Результаты поиска

Содержание 811 series

Отзывы:

Бренды по названию

Популярные бренды