manualshive.com logo in svg

Taylor 811 series, Руководство оператора

Поделиться
Скачать
Taylor 811 series Скачать руководство пользователя страница 12

3-2  

SAFETY

Model 811, 813, 819, 821 Series 

Safety 

3

 

IMPORTANT! DO NOT 

use a water jet or 

spray excessive water on or anywhere near the grill.

 

Failure to follow this instruction may result in serious 
electrical shock and cause permanent electrical and 
mechanical damage to internal parts.

Failure to follow this instruction may result in:

•

 Serious electrical shock

•

Burns from hot steam

•

Liquid collecting inside the grill and 

destroying electrical components

WARNING!

 This machine must be isolated 

from all combustible construction and materials including, 
but not limited to walls, partitions, furniture, floors, 
curtains, paper, boxes, and decorations. Failure to 
comply may result in fire and cause destruction and 
severe injury.

WARNING!

 For your safety

 DO NOT

 store or 

use gasoline or other flammable vapors or liquids in the 
vicinity of this or any other machine

.

USE EXTREME CAUTION

! while setting up, 

operating, and cleaning the grill.

•

Avoid coming in contact with hot grill surfaces or 

with hot grease.

•

DO NOT 

prepare or remove product without 

proper equipment.

•

DO NOT 

allow untrained personnel to operate 

this grill.

Failure to follow these instructions can result in burn 
injuries.

WARNING! DO NOT 

use cold water or ice to 

cool the upper platen or the lower cook surface. Failure 
to follow this instruction may result in:

•

 Serious electrical shock

•

Burns from hot steam

•

Liquid collecting inside the grill and 

destroying electrical components

CAUTION!

 Take caution to protect eyes, 

lungs, and all parts of the body from potential harm when 
using any chemical cleaner. Failure to follow this 
instruction may result in a chemical burn.

NOTICE! DO NOT

 use any abrasives or 

cleaners other than approved food service cleaners and 
degreasers. Failure to comply may cause illness to the 
consumer and may also damage grill surfaces.

CAUTION!

 This grill must be installed on a 

level surface. Failure to comply may result in personal 
injury or machine damage.

!

!

!

!

!

Содержание 811 series



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды