Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 85

Страница: 85 / 196

Maintenance, Service, and Repair

Brakes

Page 17

REPAIR THE MASTER CYLINDER

NOTE: Hydraulic brake system components must be kept clean. Make

sure your work area is free from dirt and debris and will contain
any brake fluid spills.

Remove the master cylinder from the vehicle. See

Replace the Master Cylinder

section .

Drain all fluid from the master cylinder and discard.

Remove the rubber boot.

Depress the plunger and remove the plunger spring clip retainer.

Pull the plunger and all seals out of the master cylinder bore.

Thoroughly clean, inspect and replace parts as required.

If any damage is found in the bore of the master cylinder then it must be replaced.

Lubricate all parts with clean brake fluid from a sealed container.

Reassemble in reverse order.

If the master cylinder is not to be immediately installed onto a vehicle, plug the brake line fitting hole to
prevent any contaminates from entering the master cylinder.

Содержание B0-T48-48 Taylor Truck T48





































































































































































































Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Бренды по названию

Популярные бренды

Taylor-Dunn B0-T48-48 Taylor Truck T48, Руководство пользователя

Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Бренды по названию

Популярные бренды