Taylor-Dunn B0-T48-48 Taylor Truck T48 Скачать руководство пользователя страница 71

Страница: 71 / 196

Maintenance, Service, and Repair

Brakes

Page 3

Rotor removed for clarity. The rotor does not
have to be removed for this procedure.

Do not use a rotor that is

worn beyond its service

limits. A rotor worn beyond

its service limits could fail

and cause loss of brakes

resulting in severe bodily

injury and/or property

damage.

Current Taylor-Dunn

brakes are asbestos free. However, there is

the possibility that the original brakes were replaced with aftermarket

parts containing asbestos. Since this possibility exists, all brake parts

should be handled as if they contain asbestos. Refer to Appendix C for

recommended handling precautions.

Disc Brake Rotor

NOTE: The front brake rotor is an integral part of the front hub. If the brake

rotor is worn beyond its service limits, then the front hub must be
replaced. Refer to

Front Axle Service

for information on replacing

the front hub.

NOTE: Depending on the rear axle configuration, the rear brake rotor may

be an integral part of the rear axle. If the brake rotor is worn beyond
its service limits, then the rear axle must be replaced. Refer to

Transmission

section for information regarding replacing the rear

axle

NOTE: The wheel must be removed to accurately measure the rotor

thickness. Refer to

Tires and Wheels

section for information on

removing the wheel.

1. Measure the run out of the rotor at its maximum

diameter. If the run out exceeds 0.005, then the rotor
must be machined. Do not machine the rotor beyond
its service limits.

NOTE: A bent axle or damaged rear axle could

cause excessive brake rotor run out.

2. Measure the thickness of the brake rotor in 3 places.

If the brake rotor thickness is less than 0.20-inches,
then the rotor must be replaced.

Содержание B0-T48-48 Taylor Truck T48





































































































































































































Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Бренды по названию

Популярные бренды

Taylor-Dunn B0-T48-48 Taylor Truck T48, Руководство пользователя

Результаты поиска

Содержание B0-T48-48 Taylor Truck T48

Отзывы:

Бренды по названию

Популярные бренды