Tarm Biomass Bonus Plus 30 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 55

Tarm Biomass Bonus Plus 30 Скачать руководство пользователя страница 6

Bonus Plus Instructions Tarm Biomass 1-800-782-9927 Version 11/14 Page 6

This product is provided with a limited warranty which is described in Section 7.0 of this manual. The
warranty is contingent upon the successful and legal installation of the boiler. At a minimum, the in-
stallation, adjustment, start up, service, and maintenance of this product must be performed by a li-
censed professional heating system installer. Where applicable, the installation must be

inspected and

accepted by the legally responsible entity. Conditions described in the text of the warranty for keeping
it in force must be followed by the owner/ system operator.

If the boiler has been purchased through a dealer, the warranty claim must be made to the dealer. Oth-
erwise, claims may be made directly to Tarm Biomass.

Please read the literature enclosed by the manufacturer regarding the various accessory devices. These
devices are warranted by the manufacturer, NOT BY Tarm Biomass These accessory devices must be
installed and used according to the recommendations of the manufacturer.

Failure to follow these instructions could result in property damage, bodily injury, or death. All boilers
must be installed in accordance with national, state, and local plumbing, heating, and electrical codes
and the regulations of the serving electric, water, and gas utilities. Contact local building or fire offi-
cials before installation about restrictions and installation inspection requirements in your area. This
boiler is safety tested and listed. The Bonus Plus boiler does not carry an ASME stamp.

The instructions in this manual and in supporting documentation (additional instructions, diagrams,
and component information provided by Tarm Biomass) must be followed. If the instructions are in
conflict with local code requirements, the local code requirements will prevail. When in doubt, contact
Tarm Biomass.

The manual and supporting documentation must be retained by the owner/ system operator for
reference and future use.

The installer is responsible for familiarizing the owner/ system operator with all aspects of boiler op-
erations, safety procedures, monitoring and cleaning requirements, shut down procedures, and annual
maintenance requirements.

Introduction > Foreword

«
...
4
5
6
7
8
...
»

Содержание Bonus Plus 30
























































Отзывы:

Нет отзывов