Tarm Biomass Bonus Plus 30 Скачать руководство пользователя | Manualshive

Страница: 13 / 55

background image

Bonus Plus Instructions Tarm Biomass 1-800-782-9927 Version 11/14 Page 13

2.4 Building Requirements



The boiler must be connected to a tile-lined masonry

chimney

or to a factory-built Type UL

103 HT approved chimney in good condition. See the details in

Section 3.2



A dedicated supply of

fresh combustion

air provided near the boiler is recommended for effi-

cient, safe operation. This supply must not be directly connected to the boiler.



Installation on a non-combustible floor only.



A dedicated 120 VAC

power supply is required (See Section 3.4.9).



Revision of

existing heating system

piping may be appropriate to properly utilize the equip-

ment. Although Tarm Biomass can provide advice and design detail on the integration of this
boiler with the heating system of the building, the ultimate responsibility for the performance
of the system rests with the installer.



Please observe the guidelines and the various

national and local regulations.



Bonus Plus

boilers are designed and approved as heaters for hot water systems with permissi-

ble outflow temperatures of up to 203 ºF (95 ºC).

2.5 Owner Responsibilities

Successful operation of this boiler will require daily involvement by the owner/system operator.

Biomass boilers operate differently from fossil fuel boilers, requiring more oversight and a diligent
cleaning regimen.



The owner/system operator is responsible for correct operation of the boiler per guidelines in
Sections 4.0 and 5.0 of this manual.



Incorrect operation can reduce the boiler life.

Product Description and Requirements for Safe Operation > Building Requirements

WARNING

Risk of Fire!



Do not operate with flue draft exceeding –.10 (-2.54mm) water column.



Do not operate with fuel loading or ash removal doors open.



Do not store fuel or other combustible material within marked installation clear-
ances.



Inspect and clean flues and chimney regularly.



Do not use chemicals to start unit firing.

CAUTION

Hot Surfaces!



Keep children away.



Do not touch during operation.



Maximum draft marked on nameplate.

☼

DANGER

Risk of Fire or Explosion!

Do not burn garbage, gasoline, gasoline type lantern fuel, kerosene, charcoal lighter fluid,
drain oil, or other flammable liquids to start or “freshen up” a fire in the boiler.

«
...
11
12
13
14
15
...
»

Содержание Bonus Plus 30
























































Отзывы:

Нет отзывов

Похожие инструкции для Bonus Plus 30

Бренд: H2O Страницы: 50

Vitorond 200 Type VR2

Бренд: Viessmann Страницы: 16

Tahiti Condensing 24 kW Combi (KC)

Бренд: Fondital Страницы: 56

RESIDENCE 25 KIS

Бренд: Riello Страницы: 140

Бренд: Nieco Страницы: 40

BRITONY System II 80

Бренд: C&M Страницы: 12

Бренд: Biasi Страницы: 48

Бренд: Navien Страницы: 29

Бренд: Henrad Страницы: 4

Бренд: Marco Страницы: 1

Бренд: Chaffoteaux & Maury Страницы: 12

Бренд: Baxi Страницы: 20

Format Slim HE 25 T

Бренд: Hermann Страницы: 36

Ultra-Max Lava Rock Gas Char-Broilers 8024CB

Бренд: Star Manufacturing Страницы: 2

Star-Max Lava Rock Gas Char-Broilers 6015CBD

Бренд: Star Manufacturing Страницы: 2

Бренд: Star Manufacturing Страницы: 7

Бренд: Electric Heating Company Страницы: 20

Main Eco Elite Combi 25

Бренд: Main Heating Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды