Tarm Biomass Bonus Plus 30 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 55

Tarm Biomass Bonus Plus 30 Скачать руководство пользователя страница 15

Bonus Plus Instructions Tarm Biomass 1-800-782-9927 Version 11/14 Page 15

The boiler must be installed with the

minimum installation clearances

to combustible materials out-

lined below. Clearances may only be reduced by means approved by the regulatory authorities.

Recommended Distances in the Boiler Room

Units

Bonus Plus 30

A-Minimum Clearance for Blower Maintenance

Inches

21

B-Minimum Clearance to Combustibles

Inches

12

C-Minimum Distance for Cleaning and Maintenance Tasks

Inches

21

D-Minimum Clearance to Combustibles

Inches

36

E-Minimum Clearance to Combustibles

Inches

24

F-Minimum Distance for Combustibles to Pipe

Inches

18

G-Maximum Distance for Flue Pipe

Feet

0-4

H-Ideal Location for Draft Regulator (Barometric Damper)

-

-

Boiler Installation & Start-up > Planning

CAUTION

DO NOT INSTALL THIS BOILER IN A MOBILE HOME.

There is no safe way this boiler

can be installed inside a mobile home.

☼

«
...
13
14
15
16
17
...
»

Содержание Bonus Plus 30
























































Отзывы:

Нет отзывов