manualshive.com logo in svg

Tarm Biomass Bonus Plus 30, Инструкция по установке и эксплуатации, Страница: 23 / 55

Поделиться
Скачать
Tarm Biomass Bonus Plus 30 Скачать руководство пользователя страница 23

 

Bonus Plus Instructions      Tarm Biomass   1-800-782-9927   Version 11/14          Page 23 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

3.4.9 Installing the Overheat Aquastat 

The Honeywell L4008B aquastat provided with this boiler must be installed and wired in parallel with 
the thermostat on the zone with the most heating capacity in the main living area (dump zone). Upon 
reaching the aquastat set point, the dump zone will be activated, pulling heat away from the boiler.  

                                                                

Boiler Installation & Start-up >  Connections to the Boiler 

 

Remove left knock-out on side panel. 
The side panel can now be re-installed.

 

The Honeywell L6006A aquastat can now 
be attached to sensor well. (Note: Image 
does not show side panel installed.) 

Find the spare sensor well #8 located on 
the top of the boiler (located on the right 
side of boiler). Remove the existing sen-
sor well.

 

Replace with new ½” sensor well.

 

The bulb for the Honeywell L4008B over-
heat aquastat can now be installed. Top 
panel can also be re-installed. 

Содержание Bonus Plus 30
























































Отзывы:

Нет отзывов