TallyGenicom 6300 Series Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 175

TallyGenicom 6300 Series Скачать руководство пользователя страница 46

6300 Series Maintenance Manual

40

Shuttle Fault

If the control processor detects the shuttle operating either
above or below the proper frequency, it shuts down the shuttle
and attempts to restart it. If the shuttle still operates
incorrectly after three consecutive attempts, the Control
Processor goes Offline, and the Shuttle Fault message is
displayed. Depress the Clear key, then put the printer back

Online. If this doesn’t work, turn the power switch off, then

back on again. If the error condition persists after performing
the above actions, begin replacing shuttle control components.

Testing Hardware

The printer is performing internal diagnostic tests when the
printer is powered up. If this message does not clear after a
few seconds, then the Main CPU is dead. Under normal
circumstances there is no corrective action. If the message
does not clear automatically, replace the Controller Board.

«
...
44
45
46
47
48
...
»

Содержание 6300 Series
















































































































































































Отзывы:

Нет отзывов