TallyGenicom 6300 Series страница 28 Скачать руководство пользователя

Страница: 28 / 175

6300 Series Maintenance Manual

2.2.3.2

Report

This parameter has fifteen selections. The selections Current Config, All Configs, Configs 1-10

and Calibrations generate printouts. The second pair of reports (LastFault and Version) are

displays. The Report Parameter is located in the Config Menu, under the Printer Category.

Report selections

Configs

Prints a report showing the setups of the configurations.

Calibrations

Prints a report showing the current values of the Paper Out and Paper Motion

sensors and the hammer lead time and shuttle amplitude.

Last Fault

The Control Panel Display shows the Last Fault that occurred.

Version

The Control Panel Display shows the version number of the currently installed

firmware.

To clear the displays, depress any key on the printer control panel.

Selecting a Printer Report

Step 1.

Take the printer Offline.

Step 2.

Depress the

MENU

key to enter the multilevel menu system, then scroll (

▲



Key) to

the Config menu. Press

ENTER

Step 3.

Scroll (

▲



Key) until the Printer Category displays. Press

ENTER

Step 4.

Scroll (

▲



Key) until the Report Parameter is displayed. Press

ENTER

Step 5.

Scroll (

▲



Key) to the desired selection.

Step 6.

Press

ENTER

to begin the report printout or display.

Содержание 6300 Series















































































































































































Результаты поиска

Содержание 6300 Series

Отзывы:

Похожие инструкции для 6300 Series

Бренды по названию

Популярные бренды

TallyGenicom 6300 Series, Руководство по обслуживанию

Результаты поиска

Содержание 6300 Series

Отзывы:

Похожие инструкции для 6300 Series

Бренды по названию

Популярные бренды