Synopsys DesignWare ARC AXC003 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 145

Synopsys DesignWare ARC AXC003 Скачать руководство пользователя страница 67

67

Controlling the Memory Map

DesignWare ARC AXC003 CPU Card User Guide

Version 6323-018

Synopsys, Inc.

May 2017

Table 26

AXI Tunnel Memory Map After Pre-Bootloader Execution (ARC HS34 / HS36)

Master Address

Selected Slave

Slave Address

0xFFFF_FFFF

0x8000_0000

DDR3 SDRAM

0x7FFF_FFFF

0x0000_0000

0x7FFF_FFFF

0x0000_0000

DDR3 SDRAM

0x7FFF_FFFF

0x0000_0000

Table 27

AXI Tunnel Memory Map After Pre-Bootloader Execution (ARC HS38)

Master Address

Selected Slave

Slave Address

0xFFFF_FFFF

0x8000_0000

DDR3 SDRAM via ARC IOC port

0xFFFF_FFFF

0x8000_0000

0x7FFF_FFFF

0x0000_0000

DDR3 SDRAM

0x7FFF_FFFF

0x0000_0000

7.3 Controlling the Memory Map

Setting Up the AXI Masters on the AXC003 CPU Card

Control registers are available for each AXI master (for each core and for the AXI tunnel) to
customize its memory map. The full 4 GByte AXI memory map is partitioned into 16 address
apertures of 256 Mbytes each:

aperture[0]:

base address is

0x0000_0000

aperture[1]:

base address is

0x1000_0000

aperture[2]:

base address is

0x2000_0000

...

aperture[15]:

base address is

0xF000_0000

The address map configuration consists of two steps for each 256 MByte aperture within the
AXI address space of an AXI master.

First, a target slave is selected from the list shown in Table 28

on page

68. Then, the desired

address offset within the memory map of the target slave is programmed. This offset can be
selected in steps of 256 MBytes. The specified offset refers to the address offset within the
target slave only; the base address of the aperture is not taken into account.

«
...
65
66
67
68
69
...
»

Содержание DesignWare ARC AXC003


















































































































































Отзывы:

Нет отзывов