Synopsys DesignWare ARC AXC003 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 145

Synopsys DesignWare ARC AXC003 Скачать руководство пользователя страница 49

49

AXC003 Processor FPGA Overview

DesignWare ARC AXC003 CPU Card User Guide

Version 6323-018

Synopsys, Inc.

May 2017

Note

The AXC003 Processor FPGA includes a pushbutton labeled

SW801 CONF

. This

pushbutton is for reconfiguring the CPU card FPGA. Pushing this button forces loading
the ARC CPU image to the FPGA, depending on the SW802 dipswitch settings

Debug

The ARC cores provide debug access using an IEEE 1149.1 JTAG port. In the AXC003
Processor FPGA the JTAG ports of the different ARC cores are daisy-chained into a JTAG
chain, where the data output from the first core becomes the data input to the second core
and so forth; the control and clock signals are common to all the cores in the chain. The JTAG
chain for the AXC003 Processor FPGA is shown in Figure 30.

JTAG Daisy-Chain

To distinguish between the individual cores in the JTAG chain, each core has a unique JTAG
IDCODE as listed in Table 11.

Table 11

JTAG ID Codes

Core

JTAG ID bit [31:0]

ARC ID

CPUNUM

ARC HS36

0x2014_24B1

0x0553

1

ARC HS38x2, core 1

0x2000_24B1

0x0053

1

ARC HS38x2, core 2

0x2004_24B1

0x0153

2

«
...
47
48
49
50
51
...
»

Содержание DesignWare ARC AXC003


















































































































































Отзывы:

Нет отзывов