Syneron Candela VelaShape III Скачать руководство пользователя страница 8

Страница: 8 / 86

Before You Start

PB81499EN

1. B

EFORE

TART

Warning

●

Read this manual to become familiar with all safety requirements
and operating procedures before attempting to operate the system.

●

Any intense optical energy or radio frequency (RF) device can
cause injury if used improperly.

●

High voltage is present inside the system. Always be aware of the
possible dangers and take proper safeguards as described in this
manual.

●

The VelaShape III system must be serviced only by Syneron
Medical Ltd. qualified personnel.

Conventions Used in this Manual

The following conventions in the form of notes, cautions and warnings are used
in this manual:

Note

The content of this

Note

offers general information that is important to

keep in mind.

Caution

alerts the user to the possibility of a potentially hazardous

situation which, if not avoided, may result in minor or moderate injury to
the user or damage to the equipment.

Warning

alerts the user to the possibility of injury, death, or serious

adverse reactions associated with the use or misuse of the system.

Содержание Candela VelaShape III























































































Результаты поиска

Содержание Candela VelaShape III

Отзывы:

Syneron Candela VelaShape III, Руководство пользователя системы, Страница: 8 / 86

Результаты поиска

Содержание Candela VelaShape III

Отзывы: