Syneron Candela VelaShape III Скачать руководство пользователя страница 77

Страница: 77 / 86

VelaShape III User Manual Maintenance

PB81499EN

Cleaning the System Air Filter

While the system air filter should be cleaned at least once a week, the filter cup
needs to be checked daily and cleaned according to the amount of dust and debris
that accumulates.

To clean the system air filter (see Figure 58):

Turn the system off.

Open the cover of the system's rear utility cabinet to access the filter
assembly.

Release Screw # 1 on the bottom of the filter cup to open the cup and wipe off
the dust and debris.

Release Screw # 2 to remove the filter, wash it with water and soap and set it
aside to dry.

When the filter is completely dry, fit it back into place, or put a new filter and
secure the filter cup using the screws.

The same filter may be re-used after washing. It should be discarded when it
is no longer white after cleaning.

Caution

Be sure that the filter is completely dry before re-assembling.

Figure 58: Cleaning the Air Filter

Содержание Candela VelaShape III























































































Результаты поиска

Содержание Candela VelaShape III

Отзывы:

Syneron Candela VelaShape III, Руководство пользователя системы, Страница: 77 / 86

Результаты поиска

Содержание Candela VelaShape III

Отзывы: