Syneron Candela VelaShape III Скачать руководство пользователя страница 79

Страница: 79 / 86

VelaShape III User Manual Troubleshooting

PB81499EN

Table 4: System Errors Messages Displayed On Screen and/or Applicator Panel

Message

Symptom

Corrective Action

Improve Vacuum
Seal

Vacuum is not implemented
correctly upon the skin.

●

Remove and clean the

applicator cover.

●

Replace the cover filter.

●

Put on a new cover.

●

Make sure the patient skin is

cleaned and shaved.

RF Out of Range

The system cannot apply RF
correctly.

●

Make sure there is a good

vacuum seal between the
applicator cover and patient
skin,

●

Make sure there is an

adequate amount of gel.

●

Make sure the applicator is

placed on the skin
appropriately.

No applicator, No
Tip

System freezes, no RF or IR
pulses emitted to the patient's
skin even if footswitch/trigger
is pressed.

●

Let go of footswitch/trigger and

make sure that the applicator
and tip are well connected and
sealed.

●

Let go of footswitch/trigger and

wait 10 minutes for the system
to recognize the applicator and
tip.

●

If after 10 minutes the system

does not recognize the
applicator and tip restart the
system.

●

If after restart the system does

not recognize the applicator
and tip unplug other medical
devices in the room and restart
the system again.

Содержание Candela VelaShape III























































































Результаты поиска

Содержание Candela VelaShape III

Отзывы:

Syneron Candela VelaShape III, Руководство пользователя системы, Страница: 79 / 86

Результаты поиска

Содержание Candela VelaShape III

Отзывы: