Syneron Candela VelaShape III Скачать руководство пользователя страница 52

Страница: 52 / 86

Cellulite and Circumference Treatment

PB81499EN

Note

The most accurate skin temperature is read directly
underneath the IR thermometer aperture.

Applicator Positioning

Position the applicator perpendicular to the skin and apply light
but sufficient pressure to ensure good contact.

Test Spot

Before starting treatment, test a small area with the selected parameters and wait
several minutes to observe the results.

Treatment Technique: Identifying the Applicator and Cover

Treatment Using the VContour Applicator

Treatment can performed with two different protocol modes:

●

Circumference Mode

●

Deep Mode

The

Circumference Mode

treatment protocol for circumference reduction

supports two types of covers:

●

When treating larger treated areas (such as abdomen, arms, thighs) use the

Medium Cover

as a standalone.

●

When treating smaller treated areas (such as submental) use the

Small

Cover

as a standalone.

The

Deep Mode

treatment protocol for focal fat deposits supports a combination

of two covers. Treatment is performed using the

Large Cover

followed by the

Medium Cover

and it is used for different body areas (such as: flanks, , middle-

back, etc.).

Содержание Candela VelaShape III























































































Результаты поиска

Содержание Candela VelaShape III

Отзывы:

Syneron Candela VelaShape III, Руководство пользователя системы, Страница: 52 / 86

Результаты поиска

Содержание Candela VelaShape III

Отзывы: