Suzuki GRAND VITARA JB416 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 474

background image

IMPORTANT

WARNING/CAUTION/NOTE

Please read this manual and follow its instructions carefully. To emphasize special information, the words

,

and

NOTE have special meanings. Pay special attention to the messages high-

lighted by these signal words.

The circle with a slash in this manual means “Don’t do this” or “Don’t let this happen”.

WARNING

!

CAUTION

!

Indicates a potential hazard that could result in death or injury.

WARNING

!

Indicates a potential hazard that could result in vehicle damage.

CAUTION

!

NOTE:

Indicates special information to make maintenance easier or instructions clearer.

This service manual is intended for authorized Suzuki dealers and qualified service technicians only.
Inexperienced technicians or technicians without the proper tools and equipment may not be able to
properly perform the services described in this manual.
Improper repair may result in injury to the technician and may render the vehicle unsafe for the driver
and passengers.

WARNING

!

For vehicles equipped with a Supplemental Restraint (Air Bag) System:
• Service on and around the air bag system components or wiring must be performed only by an

authorized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under
“General Description” in air bag system section in order to confirm whether you are performing ser-
vice on or near the air bag system components or wiring. Please observe all WARNINGS and “Ser-
vice Precautions” under “On-Vehicle Service” in air bag system section before performing service
on or around the air bag system components or wiring. Failure to follow WARNINGS could result in
unintentional activation of the system or could render the system inoperative. Either of these two
conditions may result in severe injury.

• If the air bag system and another vehicle system both need repair, Suzuki recommends that the air

bag system be repaired first, to help avoid unintended air bag system activation.

• Do not modify the steering wheel, instrument panel or any other air bag system component on or

around air bag system components or wiring. Modifications can adversely affect air bag system
performance and lead to injury.

• If the vehicle will be exposed to temperatures over 93 °C (200 °F), for example, during a paint baking

process, remove the air bag system components, that is air bag (inflator) modules, SDM and/or seat
belt with pretensioner, beforehand to avoid component damage or unintended activation.

WARNING

!

1
2
3
...
»

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA JB416

Бренд: Daihatsu Страницы: 1718

Бренд: Hama Страницы: 6

Бренд: GMC Страницы: 499

Бренд: Kia Страницы: 290

WrapAround Windjammer

Бренд: Bestop Страницы: 7

2003 Silhouette

Бренд: Oldsmobile Страницы: 466

Бренд: Curt Manufacturing Страницы: 4

Бренд: Whispbar Страницы: 112

Бренд: Ford Страницы: 4378

Бренд: Toyota Страницы: 549

Бренд: Yenkee Страницы: 22

Бренд: KAP Страницы: 22

2002 Accord Coupe

Бренд: Honda Страницы: 367

BLADE-AL-HK4-EN

Бренд: iDataLink Страницы: 35

Бренд: Kargo Master Страницы: 7

EVO ONE THAR-GM7

Бренд: Fortin Страницы: 11

20111 Highlander

Бренд: Toyota Страницы: 9

Бренд: SAN HIMA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды