Supero AS-1011M-UR Скачать руководство пользователя

Страница: 51 / 104

Chapter 5: Advanced Motherboard Setup

5-17

Chassis Intrusion

A Chassis Intrusion header is located

at JL1. Attach the appropriate cable

to inform you of a chassis intrusion.

Chassis Intrusion

Pin Defi nitions (JL1)

Pin# Defi nition

Battery voltage

Intrusion signal

Wake-On-LAN

The Wake-On-LAN header is desig-

nated JWOL. See the table on the

right for pin defi nitions. You must

have a LAN card with a Wake-On-LAN

connector and cable to use the Wake-

On-LAN feature.

(Note: Wake-On-LAN from S3, S4, S5

are supported by LAN1. LAN2 sup-

ports Wake-On-LAN from S1 only.)

Wake-On-Ring

The Wake-On-Ring header is desig-

nated JWOR. This function allows

your computer to receive and "wake-

up" by an incoming call to the modem

when in suspend state. See the table

on the right for pin defi nitions. You

must have a Wake-On-Ring card and

cable to use this feature.

Wake-On-Ring

Pin Defi nitions

(JWOR)

Pin# Defi nition

Ground (Black)

Wake-up

Wake-On-LAN

Pin Defi nitions

(JWOL)

Pin# Defi nition

+5V Standby

Ground

Wake-up

Содержание AS-1011M-UR









































































































Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды

Supero AS-1011M-UR, Руководство пользователя

Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды