Supero AS-1011M-UR Скачать руководство пользователя

Страница: 65 / 104

Chapter 6: Advanced Chassis Setup

6-3

6-3 System

Fans

Three 4-cm heavy duty counter-rotating fans provide the cooling for the 1011M-UR.

Each fan unit is actually made up of two fans joined back-to-back, which rotate in

opposite directions. This counter-rotating action generates exceptional airfl ow and

works to dampen vibration levels. It is very important that the chassis top cover is

properly installed and making a good seal in order for the cooling air to circulate

properly through the chassis and cool the components. See Figure 6-2.

System Fan Failure

Fan speed is controlled by system temperature via a BIOS setting. If a fan fails,

the remaining fan will ramp up to full speed and the Universal Information LED on

the control panel will blink on and off quickly. Replace any failed fan at your earli-

est convenience with the same type and model (the system can continue to run

with a failed fan). Remove the top chassis cover while the system is still running

to determine which of the two fans has failed. Then power down the system be-

fore replacing a fan. Removing the power cords is also recommended as a safety

precaution.

Replacing

System

Fans

1. Removing a fan

After turning off the power to the system, fi rst remove the chassis cover and unplug

the fan cable from the motherboard. Unscrew the failed blower fan from the chassis

and pull it completely out from the motherboard.

2. Installing a new fan

Replace the failed fan with an identical 4-cm, 12 volt fan (available from Supermicro:

p/n FAN-0086L). Push the new fan into the vacant space in the housing while mak-

ing sure the arrows on the top of the fan (indicating air direction) point in the same

direction as the arrows on the other fans. Reposition the fan housing back over

the two mounting posts in the chassis, then reconnect the fan wires to the same

chassis fan headers you removed them from. Power up the system and check that

the fan is working properly and that the LED on the control panel has turned off.

Finish by replacing the chassis cover.

Содержание AS-1011M-UR









































































































Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды

Supero AS-1011M-UR, Руководство пользователя

Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды