Supero AS-1011M-UR Скачать руководство пользователя страница 75

Страница: 75 / 104

Chapter 7: BIOS

7-3

PS/2 Mouse Support

Set this value to allow the PS/2 mouse support to be modifi ed. The options are

Enabled, Disabled and

Auto

Wait for ‘F1’ If Error

Select

Enabled

to activate the "Wait for 'F1' if Error" function.

Hit ‘DEL’ Message Display

Select Enabled to display Setup Message when the user hits the DEL key. The

options are

Enabled

and Disabled.

Interrupt 19 Capture

Select

Enabled

to allow ROMs to trap Interrupt 19. The options are Enabled

and Disabled.

OS Installation

Change this setting if using a Linux operating system. The available options

are

Other

and Linux.

ACPI Mode

Use this setting to determine whether ACPI mode will be used. The options

are

Yes

and No.

ACPI Version Features

Use this setting the determine which ACPI version to use. Options are

ACPI

v1.0

, ACPI v2.0 and ACPI v3.0.

ACPI APIC Support

Select Enabled to allow the ACPI APIC Table Pointer to be included in the RSDT

pointer list. The options are

Enabled

and Disabled.

ACPI OEMB Table

This setting when enabled will include an OEMB table pointer to pointer lists.

Options are

Enabled

and Disabled.

Headless Mode

Use this setting to Enable or

Disable

headless operation mode through ACPI.

Содержание AS-1011M-UR









































































































Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды

Supero AS-1011M-UR, Руководство пользователя

Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды