Supero AS-1011M-UR Скачать руководство пользователя страница 29

Страница: 29 / 104

Chapter 3: System Interface

3-3

NIC2:

Indicates network activity on LAN2 when fl ashing .

NIC1:

Indicates network activity on LAN1 when fl ashing.

HDD:

Indicates IDE channel activity. On the 1011M-UR this light indicates

SAS/SATA and/or DVD-ROM drive activity when fl ashing.

Power:

Indicates power is being supplied to the system's power supply

units. This LED should normally be illuminated when the system is operating.

3-4

Drive Carrier LEDs

SATA Drives

Each Serial ATA drive carrier has two LEDs.

Green:

When illuminated, the green LED on the front of the SATA drive car-

rier indicates drive activity. A connection to the SATA backplane enables this LED

to blink on and off when that particular drive is being accessed.

Red:

The red LED indicates two states. When blinking, it indicates the drive

is rebuilding. When solid, it indicates a drive failure. If a SATA drive fails, you

should be notifi ed by your system management software. Please refer to Chapter

6 for instructions on replacing failed SATA drives.

Содержание AS-1011M-UR









































































































Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды

Supero AS-1011M-UR, Руководство пользователя

Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды