Supero AS-1011M-UR Скачать руководство пользователя

Страница: 77 / 104

Chapter 7: BIOS

7-5

Floppy/IDE/SATA Confi guration

Floppy A

Move the cursor to these fi elds via up and down <arrow> keys to select the fl oppy

type. The options are Disabled, 360 KB 5 1/4", 1.2 MB 5 1/4", 720 KB 3½",

1.44

MB 3½”

, and 2.88 MB 3½".

Floppy B

Move the cursor to these fi elds via up and down <arrow> keys to select the fl oppy

type. The options are

Disabled

, 360 KB 5 1/4", 1.2 MB 5 1/4", 720 KB 3½", 1.44

MB 3½

”

, and 2.88 MB 3½".

Onboard Floppy Controller

Use this setting to

Enable

or Disable the onboard fl oppy controller.

Onboard IDE Controller

There is a single fl oppy controller on the motherboard, which may be

Enabled

Disabled with this setting.

Serial ATA Devices

This setting is used to determine if SATA drives will be used and how many. Op-

tions are Disabled, Device 0 and

Device 0/1

nVidia RAID Function

This setting is used to Enable or

Disable

the nVidia ROM.

Primary IDE Master/Slave

Highlight one of the items above and press <Enter> to access the submenu for

that item.

Type

Select the type of device connected to the system. The options are Not Installed,

Auto

, CDROM and ARMD.

LBA/Large Mode

LBA (Logical Block Addressing) is a method of addressing data on a disk drive.

The options are Disabled and

Auto

Содержание AS-1011M-UR









































































































Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды

Supero AS-1011M-UR, Руководство пользователя

Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды