Supero AS-1011M-UR Скачать руководство пользователя

Страница: 48 / 104

5-14

AS1011M-UR User's Manual

Power Fail LED

The Power Fail LED connection is

located on pins 5 and 6 of JF1. Refer

to the table on the right for pin defi ni-

tions. This feature is only available

for systems with redundant power

supplies.

Power Fail LED

Pin Defi nitions (JF1)

Pin# Defi nition

Vcc

Control

Reset Button

The Reset Button connection is lo-

cated on pins 3 and 4 of JF1. Attach

it to the hardware reset button on the

computer case. Refer to the table on

the right for pin defi nitions.

Power Button

The Power Button connection is

located on pins 1 and 2 of JF1. Mo-

mentarily contacting both pins will

power on/off the system. This button

can also be confi gured to function

as a suspend button (see the Power

Button Mode setting in BIOS). To turn

off the power when set to suspend

mode, depress the button for at least

4 seconds. Refer to the table on the

right for pin defi nitions.

Universal Serial Bus Ports
(USB0/1)

Two Universal Serial Bus ports

(USB2.0) are located beside the

mouse/keyboard ports. See the table

on the right for pin defi nitions.

Reset Button

Pin Defi nitions (JF1)

Pin# Defi nition

Reset

Ground

Power Button

Pin Defi nitions (JF1)

Pin# Defi nition

PW_ON

Ground

Universal Serial Bus Ports

Pin Defi nitions (USB0/1)

USB0
Pin # Defi nition

USB1
Pin # Defi nition

+5V

PO-

PO+

Ground

Содержание AS-1011M-UR









































































































Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды

Supero AS-1011M-UR, Руководство пользователя

Результаты поиска

Содержание AS-1011M-UR

Отзывы:

Похожие инструкции для AS-1011M-UR

Бренды по названию

Популярные бренды