Supermicro SUPERSERVER 5028TK-HTR Скачать руководство пользователя страница 97

Страница: 97 / 138

7-13

Chapter 7: BIOS

L0s Support

When this item is set to Disable, II0 will not put its transmitter in the L0s state.
The options are

Disable

and Enable.



IOAT (Intel® IO Acceleration) Configuration

Relaxed Ordering

Select Enable to enable Relaxed Ordering support which will allow certain
transactions to violate the strict-ordering rules of PCI bus for a transaction to
be completed prior to other transactions that have already been enqueued. The
options are

Disable

and Enable.



IIO Generation Configuration

IIO

ACPI (Advanced Configuration Power Interface)

Select Enable to enable Advanced Configuration Power Interface (ACPI) support
for the IO device specified by the user. The options are

Enable

and Disable.



Intel VT for Directed I/O (VT-d)

Intel VT for Direct I/O (VT-d)

PCI Express Global Options

The section allows the user to configure the following PCI-E global options:

WA 4167453

Select Enable for WA 4167453 support. The options are

Disable

and Enable.

NoSnoop (No Snoop) Config. (Configuration)

Use this item to configure the no-snoop mode setting for each PCI-E device.

The options are

VC0/VCP/VC1

and VC1.

Halt On DMI Degradation

Select Enable to put the system on hold during DMI width/link degradation.

The options are

Disable

and Enable.

Power Down Unused Ports

Select Disable to power down the ports that are not being used. The options are
Disable and

Disable Unused Ports (No IIO Clock Gating)

Содержание SUPERSERVER 5028TK-HTR











































































































































Результаты поиска

Содержание SUPERSERVER 5028TK-HTR

Отзывы:

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 5028TK-HTR, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5028TK-HTR

Отзывы:

Бренды по названию

Популярные бренды