manualshive.com logo in svg

Supermicro SUPERSERVER 5028TK-HTR, Руководство пользователя, Страница: 8 / 138

Поделиться
Скачать
Supermicro SUPERSERVER 5028TK-HTR Скачать руководство пользователя страница 8

viii

5-8 

Connector Definitions

 ...................................................................................... 5-8

5-9 

Jumper Settings ............................................................................................ 5-10
Explanation of Jumpers ................................................................................ 5-10

5-10  Onboard Indicators ........................................................................................ 5-12
5-11   PCI-Express Slots and SATA Ports .............................................................. 5-13
5-12  Onboard Battery ............................................................................................ 5-14

Chapter 6 Advanced Chassis Setup

6-1 

Static-Sensitive Devices .................................................................................. 6-1
Precautions ..................................................................................................... 6-1
Unpacking ....................................................................................................... 6-1

6-2 

Control Panel .................................................................................................. 6-2

6-3 

Chassis Cover ................................................................................................. 6-3

6-4 

Air Shrouds ..................................................................................................... 6-4

6-5 

Checking the Airflow

 ....................................................................................... 6-5

6-6 

System Fans ................................................................................................... 6-5

Optional Fan Configurations

 ........................................................................... 6-5

6-7 

Removing and Installing the Backplane .......................................................... 6-8
Removing the Backplane ................................................................................ 6-8
Installing the Backplane ................................................................................ 6-10

6-8 

Installing the Serverboard ..............................................................................6-11
I/O Shield .......................................................................................................6-11
Permanent and Optional Standoffs ................................................................6-11

6-9 

Adapter Card Replacement........................................................................... 6-13
Installing an Add-on Card ............................................................................. 6-14

6-10  Drive Bay Installation/Removal ..................................................................... 6-15

Accessing the Drive Bays ............................................................................. 6-15

6-11  Power Supply ................................................................................................ 6-19

Power Supply Replacement .......................................................................... 6-19

Chapter 7 BIOS 

7-1   Introduction ...................................................................................................... 7-1

Starting BIOS Setup Utility .............................................................................. 7-1

How To Change the Configuration Data

 ......................................................... 7-2

How to Start the Setup Utility ......................................................................... 7-2

7-2   Main Setup ...................................................................................................... 7-3

7-3   Advanced Setup Configurations

...................................................................... 7-4

7-4   Event Logs .................................................................................................... 7-36
7-5   IPMI ............................................................................................................... 7-38
7-6 

Security Settings ........................................................................................... 7-40

SUPERSERVER 5028TK-HTR/HTTR User's Manual

Содержание SUPERSERVER 5028TK-HTR











































































































































Отзывы:

Нет отзывов