manualshive.com logo in svg

Supermicro SUPERSERVER 5028TK-HTR, Руководство пользователя

Поделиться
Скачать
Supermicro SUPERSERVER 5028TK-HTR Скачать руководство пользователя страница 111

7-27

Chapter 7: BIOS

Ipv4 PXE Support (Available when Network Stack is set to Enabled)

Select Enabled to enable Ipv4 PXE (Preboot Execution Environment) for boot sup-
port. If this feature is set to Disabled, Ipv4 PXE boot option will not be supported. 
The options are 

Enabled

 and Disabled.

Ipv6 PXE Support (Available when Network Stack is set to Enabled)

Select Enabled to enable Ipv6 PXE (Preboot Execution Environment) for boot sup-
port. If this feature is set to Disabled, Ipv4 PXE boot option will not be supported. 
The options are Enabled and 

Disabled.

Onboard Video Option ROM Type

Select Enabled to enable Option ROM support to boot the computer using a video 

device specified by the user. The options are Disabled, 

Legacy 

and EFI.

AST2400 Super IO Configuration 

Super IO Chip AST2400

Serial Port 1 Configuration/Serial Port 2 Configuration

Serial Port 1/Serial Port 2

Select Enabled to enable the onboard serial port specified by the user. The options 

are 

Enabled 

and Disabled.

Device Settings

This item displays the base I/O port address and the Interrupt Request address of 

a serial port specified by the user.

Change Port 1 Settings/Change Port 2 Settings

This feature specifies the base I/O port address and the Interrupt Request address 

of Serial Port 1 or Serial Port 2. Select

 

Auto

 for the BIOS to automatically assign 

the base I/O and IRQ address to a serial port specified. 

The options for Serial Port 1 are 

Auto

, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5, 

6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3, 
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12). 
The options for Serial Port 2 are

 Auto

, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5, 

6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3, 
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).

Serial Port 2 Attribute

Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redi-
rection. The options are COM and 

SOL

.

Содержание SUPERSERVER 5028TK-HTR











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды