manualshive.com logo in svg

Supermicro SUPERSERVER 5028TK-HTR, Руководство пользователя

Поделиться
Скачать
Supermicro SUPERSERVER 5028TK-HTR Скачать руководство пользователя страница 88

7-4

SUPERSERVER 5028TK-HTR/HTTR User's Manual

7-3   Advanced Setup Configurations

Use the arrow keys to select Advanced setup and press <Enter> to access the 
submenu items:

Warning

: Take Caution when changing the Advanced settings. An incorrect value, 

DRAM frequency or BIOS timing setting may cause the system to malfunction. When 
this occurs, restore the setting to the manufacture default setting.

Boot Feature

Quiet Boot

Use this feature to select the screen display between POST messages or the OEM 
logo at bootup. Select Disabled to display the POST messages. Select Enabled 
to display the OEM logo instead of the normal POST messages. The options are 

Enabled

 and Disabled. 

AddOn ROM Display Mode

Use this item to set the display mode for the AddOn ROM messages. Select Keep 
Current to use the current AddOn ROM Messages display setting. Select Force 
BIOS to use the AddOn ROM Messages display mode set by the system BIOS. 
The options are 

Force BIOS 

and Keep Current. 

Bootup Num-Lock State

Use this feature to set the Power-on state for the Numlock key. The options are 
Off and 

On

.

Содержание SUPERSERVER 5028TK-HTR











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды