manualshive.com logo in svg

Supermicro SUPERSERVER 5028TK-HTR, Руководство пользователя

Поделиться
Скачать
Supermicro SUPERSERVER 5028TK-HTR Скачать руководство пользователя страница 124

7-40

SUPERSERVER 5028TK-HTR/HTTR User's Manual

7-6  Security Settings

This  menu  allows  the  user  to  configure  the  following  security  settings  for  the 

system.

Password Check

Select Setup for the system to prompt for a password upon entering the BIOS setup 
utility. Select Always for the system to prompt for a password at bootup and upon 
entering the BIOS Setup utility. The options are 

Setup 

and Always.

Administrator Password

Use this feature to set the administrator password which is required before entering  
the BIOS setup utility. The length of the password should be from 3 characters 
to 20 characters long.

User Password

Use this feature to set the user password which is required to enter the BIOS 
setup utility. The length of the password should be from 3 characters to 20 char-
acters long.

VLAN

Select Enabled to enable IPMI VLAN function support. The options are 

Enabled

 

and Disabled.

Содержание SUPERSERVER 5028TK-HTR











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды