manualshive.com logo in svg

Supermicro SUPERSERVER 5028TK-HTR, Руководство пользователя

Поделиться
Скачать
Supermicro SUPERSERVER 5028TK-HTR Скачать руководство пользователя страница 53

Chapter 5: Advanced Serverboard Setup

5-3

Figure 5-2. Intel Xeon Phi x200 Processors

5-4  Processor and Heatsink

The 5028TK-HTR/HTTR is sold as complete systems with the processor and 
heatsink assembly factory installed. These components are not user serviceable 
and the user should not attempt to remove or modify these components other than 

for  adjustments  specifically  outlined  in  this  manual.  Making  other  adjustments  to 

these components risks damaging the system and voiding the system warranty.
If you believe there is a hardware problem with one of these components, please 
contact Supermicro’s technical support team or your service contact if you have 
purchased a service package for this system.

Intel® Xeon Phi™ x200

Intel® Xeon Phi™ x200

with Integrated Fabric

Содержание SUPERSERVER 5028TK-HTR











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды