manualshive.com logo in svg

Supermicro SUPERSERVER 5028TK-HTR, Руководство пользователя


Поделиться
Скачать
background image

7-22

SUPERSERVER 5028TK-HTR/HTTR User's Manual

(Port 0~ Port 5 ) Hot Plug

Select Enabled to enable hot-plugging support for a port specified by the user, 

which will allow the user to replace a SATA disk drive installed on this port without 
shutting down the system. The options are 

Enabled

 and Disabled.

(Port 0~ Port 5 ) Spin Up Device

On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE-
SET initialization to the device. The options are Enabled and 

Disabled

.

(Port 0~ Port 5 ) SATA Device Type

Use this item to specify if the SATA port specified by the user should be con

-

nected to a Solid State drive or a Hard Disk Drive. The options are 

Hard Disk 

Drive

 and Solid State Drive.

sSATA Configuration

When this submenu is selected, AMI BIOS automatically detects the sSATA devices 
installed in the system and displays the following items:

sSATA Controller

This item enables or disables the onboard sSATA controller. The options are 

En-

abled

 and Disabled. 

Configure sSATA as

Select IDE to configure an sSATA drive specified by the user as an IDE drive. Select 
AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select 
RAID to configure an sSATA drive specified by the user as a RAID drive. The op

-

tions are IDE, 

AHCI

, and RAID. 

*If  the  item  above  "Configure  sSATA  as"  is  set  to AHCI,  the  following  items  will 

display

:

Aggressive Link Power Management

When this item is set to Enabled, the sSATA AHCI controller manages the power 
usage of the sSATA link. The controller will put the link to a low power state when 
the I/O is inactive for an extended period of time, and the power state will return 
to normal when the I/O becomes active. The options are Enabled and Disabled.

sSATA Port 0~ Port 5

This item displays the information detected on the installed sSATA drive on the 
particular sSATA port.

• 

Model number of drive and capacity

Содержание SUPERSERVER 5028TK-HTR











































































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSERVER 5028TK-HTR

NEC Univerge SV8100 System Specifications preview
Univerge SV8100
Бренд: NEC Страницы: 2
Gateway 7250R Rack Mounting Instructions preview
7250R
Бренд: Gateway Страницы: 26
Intel SBXL52 - Server Compute Blade Hardware Maintenance Manual preview
SBXL52 - Server Compute Blade
Бренд: Intel Страницы: 126
Silex technology Silex Pricom SX-2000U2 Technical Specifications preview
Silex Pricom SX-2000U2
Бренд: Silex technology Страницы: 1
TYANO TS65A-B8036 Service Engineer'S Manual preview
TS65A-B8036
Бренд: TYANO Страницы: 102
Boca Systems BocaVision WT120 User Handbook Manual preview
BocaVision WT120
Бренд: Boca Systems Страницы: 28
Acrosser Technology AND-APL1E Series User Manual preview
AND-APL1E Series
Бренд: Acrosser Technology Страницы: 42
Dell PowerVault Manual preview
PowerVault
Бренд: Dell Страницы: 396
Dell PowerVault 600 Getting Started preview
PowerVault 600
Бренд: Dell Страницы: 180
Dell EqualLogic PS6010 Hardware Maintenance preview
EqualLogic PS6010
Бренд: Dell Страницы: 57
Dell PowerVault 700N Administrator'S Manual preview
PowerVault 700N
Бренд: Dell Страницы: 29
Dell PowerEdge M830 Owner'S Manual preview
PowerEdge M830
Бренд: Dell Страницы: 133
SpectraLink IP-DECT SERVER 400 Installation And Configuration Manual preview
IP-DECT SERVER 400
Бренд: SpectraLink Страницы: 221
QNAP TS-230 User Manual preview
TS-230
Бренд: QNAP Страницы: 44
Nortel CallPilot 1005r Hardware Installation preview
CallPilot 1005r
Бренд: Nortel Страницы: 74
Nortel Communication Server 100 Manual preview
Communication Server 100
Бренд: Nortel Страницы: 214
Maverick System NasDisk User Manual preview
NasDisk
Бренд: Maverick System Страницы: 58
evertz IXG CloudBridge User Manual preview
IXG CloudBridge
Бренд: evertz Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды