Supermicro 6028R-E1CR12L Скачать руководство пользователя

Страница: 80 / 140

6-6

UPER

TORAGE

YSTEM 6028R-E1CR12L User's Manual

6-6 Drive Bay Installation/Removal

Accessing the Drive Bays

You do not need to access the inside of the chassis or remove power to replace or
swap hard drives. Proceed to the next step for instructions.

Note:

Refer to the following ftp site for setup guidelines: <ftp://ftp.supermicro.com/

driver/SAS/LSI/LSI_SAS_EmbMRAID_SWUG.pdf> and Supermicro's web site for
additional inmformation < http://www.supermicro.com/support/manuals/>.

SAS/SATA Drive Installation

These drives are mounted in carriers to simplify their installation and removal from

the chassis. The carriers also help promote proper airflow for the drives. For this

reason, even empty carriers without hard drives installed must remain in the chassis.

Removing a Drive Carrier

1. Push the release button located beside the drive's LEDs.

2. Swing the handle fully out and use it to pull the drive carrier straight out (see

Figure 6-5).

Mounting a Drive in a Drive Carrier

1. To add a new hard drive, install the drive into the carrier with the printed

circuit board side facing down so that the mounting holes align with those in
the carrier.

2. Secure the drive to the carrier with screws, as shown in Figure 6-6.

Caution:

Enterprise level hard disk drives are recommended for use in Supermicro

chassis and servers. For information on recommended HDDs, visit the Supermicro
website at http://www.supermicro.com/products/nfo/storage.cfm

Содержание 6028R-E1CR12L













































































































































Результаты поиска

Содержание 6028R-E1CR12L

Отзывы:

Похожие инструкции для 6028R-E1CR12L

Бренды по названию

Популярные бренды

Supermicro 6028R-E1CR12L, Руководство пользователя

Результаты поиска

Содержание 6028R-E1CR12L

Отзывы:

Похожие инструкции для 6028R-E1CR12L

Бренды по названию

Популярные бренды