Supermicro 6028R-E1CR12L Скачать руководство пользователя

Страница: 116 / 140

7-30

UPER

TORAGE

YSTEM 6028R-E1CR12L User's Manual

MMIOHBase

Use this item to select the I/O base memory size according to memory-address
mapping for the PCH chip. The base memory size must be between 4032G to
4078G. The options are

56T

, 48T, 24T, 2T, 512G, and 256G.

MMIO High Size

Use this item to select the high I/O memory size according to memory-address
mapping for the PCH chip. The options are

256G

, 128G, 512G, and 1024G.

PCI Devices Option ROM Setting

CPU1 Slot1 PCI-E x8 OPROM/CPU1 Slot2 PCI-E x16 OPROM/CPU1 Slot3

PCI-E x8 OPROM/CPU2 Slot4 PCI-E x16 OPROM/CPU2 Slot5 PCI-E x8

OPROM/CPU2 Slot6 PCI-E x16 OPROM/CPU2 Slot7 PCI-E x16 OPROM/

Onboard Video Option ROM

Select Enabled to enable Option ROM support to boot the computer using a de-

vice installed on the slot specified by the user. The options are Disabled,

Legacy

and EFI.

Onboard LAN Option ROM Type

Select Enabled to enable Option ROM support to boot the computer using a device

installed on the slot specified by the user. The options are

Legacy

and EFI.

VGA Priority

Use this item to select the graphics device to be used as the primary video display
for system boot. The options are

Onboard

and Offboard.

Onboard LAN1 Option ROM/Onboard LAN2 Option ROM

Use this option to select the type of device installed in LAN Port1 or LAN Port2
for system boot. The default setting for LAN1 Option ROM is

PXE

, and for LAN2

Option ROM is

Disabled

Network Stack

Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Uni-

fied Extensible Firmware Interface) for network stack support. The options are

Enabled and

Disabled

Содержание 6028R-E1CR12L













































































































































Результаты поиска

Содержание 6028R-E1CR12L

Отзывы:

Похожие инструкции для 6028R-E1CR12L

Бренды по названию

Популярные бренды

Supermicro 6028R-E1CR12L, Руководство пользователя

Результаты поиска

Содержание 6028R-E1CR12L

Отзывы:

Похожие инструкции для 6028R-E1CR12L

Бренды по названию

Популярные бренды