Supermicro 6028R-E1CR12L Скачать руководство пользователя

Страница: 124 / 140

7-38

UPER

TORAGE

YSTEM 6028R-E1CR12L User's Manual

6. From the window that pops up, select "Enabled" and press <Enter>.

7. You must save your changes and reset for the changes to take effect. Scroll

to the Save & Exit tab and select "Save Changes and Reset." The TPM is
now enabled.



Intel TXT (LT-SX) Configuration

This submenu allows the user to configure the following TXT settings.

TXT Support

Select Enabled to enable Intel Trusted Execution Technology (TXT) support. The
options are

Disabled

and Enabled.

Note

: If the option for this item (TXT Support) is set to Enabled, be sure

to disable EV DFX (Device Function On-Hide) support for the system to

work properly. (EV DFX is under "IIO Configuration" in the "Chipset/North

Bridge" submenu on Page 4-11).

Note:

For more information on TPM, please refer to the TPM manual at

http://www.supermicro.com/manuals/other/AOM-TPM-9655V_9655H.pdf

Содержание 6028R-E1CR12L













































































































































Результаты поиска

Содержание 6028R-E1CR12L

Отзывы:

Похожие инструкции для 6028R-E1CR12L

Бренды по названию

Популярные бренды

Supermicro 6028R-E1CR12L, Руководство пользователя

Результаты поиска

Содержание 6028R-E1CR12L

Отзывы:

Похожие инструкции для 6028R-E1CR12L

Бренды по названию

Популярные бренды