Supermicro 6028R-E1CR12L Скачать руководство пользователя | Manualshive

Страница: 57 / 140

background image

Chapter 5: Advanced Serverboard Setup

5-11

5-6 Adding PCI Expansion Cards

The 6028R-E1CR12L can accommodate up to five PCI expansion cards in the PCI

expansion slots on the serverboard. Note that two of the slots are already populated
with the Hardware RAID controller card and the JBOD expansion card.

Installing an Add-on Card

1. Begin by removing the shield for the PCI slot you wish to populate. Make sure

that the card you are installing is supported by the slot (see table below).

2. Fully seat the card into the slot, pushing down with your thumbs evenly on

both sides of the card.

3. Finish by using a screw to secure the top of the card shield to the chassis.

The PCI slot shields protect the serverboard and its components from EMI
and aid in proper ventilation, so make sure there is always a shield covering
each unused slot.

Expansion Slot

Description

Slot1 (CPU1)

JBOD Expansion

Slot2 (CPU1)

HW RAID Controller

Slot3 (CPU1)

PCI-Express 3.0 x8 slot from CPU1

Slot4 (CPU2)

PCI-Express 3.0 x16 slot from CPU2

Slot5 (CPU2)

PCI-Express 3.0 x8 slot from CPU2

Slot6 (CPU2)

PCI-Express 3.0 x8 slot from CPU2

Slot7 (CPU2)

PCI-Express 3.0 x8 slot from CPU2

«
...
55
56
57
58
59
...
»

Содержание 6028R-E1CR12L













































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6028R-E1CR12L

Interlogix 60-875 Simon

Бренд: GE Страницы: 40

Бренд: GE Security Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: 3M Страницы: 90

Бренд: Zadako Страницы: 15

Бренд: V-Tec Страницы: 16

InTANK iR2775-S3

Бренд: Raidon Страницы: 21

Бренд: Raidon Страницы: 2

Бренд: Rafiki Protection Страницы: 32

Бренд: Hame Страницы: 26

Бренд: Xcel-Arc Страницы: 36

Бренд: Daewoo Страницы: 21

Бренд: Quell Страницы: 24

Бренд: U-Line Страницы: 39

IronKey EMS H350 Enterprise

Бренд: DataLocker Страницы: 23

Бренд: Magnavox Страницы: 24

NX-108E - Security NetworX NX-4 System

Бренд: GE Страницы: 20

CoolBloC C34 DN 32

Бренд: PAW Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды