Supermicro 6028R-E1CR12L Скачать руководство пользователя

Страница: 126 / 140

7-40

UPER

TORAGE

YSTEM 6028R-E1CR12L User's Manual



Change SMBIOS Event Log Settings

This feature allows the user to configure SMBIOS Event settings.

Enabling/Disabling Options

SMBIOS Event Log

Select Enabled to enable SMBIOS (System Management BIOS) Event Logging
during system boot. The options are

Enabled

and Disabled.

Runtime Error Logging Support

Select Enable to support Runtime Error logging. The options are

Enabled

and

Disabled. If this item is set to Enabled, the following item will be available for

configuration:

Erasing Settings

Erase Event Log

Select Yes to erase all error events in the SMBIOS (System Management BIOS)
log before an event logging is initialized at bootup. The options are

, Yes, Next

reset, and Yes, every reset.

7-4 Event Logs

This submenu allows the user to configure Event Log settings.

Содержание 6028R-E1CR12L













































































































































Результаты поиска

Содержание 6028R-E1CR12L

Отзывы:

Похожие инструкции для 6028R-E1CR12L

Бренды по названию

Популярные бренды

Supermicro 6028R-E1CR12L, Руководство пользователя

Результаты поиска

Содержание 6028R-E1CR12L

Отзывы:

Похожие инструкции для 6028R-E1CR12L

Бренды по названию

Популярные бренды