background image

24

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Installation Instructions

901140-00, 01/2021

Innovative Hearth Products
DRT63ST-B Power-Vent Direct-Vent Fireplace

Wiring: Fireplace  

(See

 Figures 34 and 35 on Page 25)

NOTE:

 These electronic appliances must be connected to the main power 

supply. The gas valve is set in place and pre-wired at the factory.

1

.  Route a 3-wire 120Vac 60Hz 1ph power supply to the appliance junc-

tion box.

2

.  Remove the electrical inlet cover plate from the side of the unit by remov-

ing the plate's securing screws (

see Figure 12 on Page 14

)

.

3

.  Remove the  cover plate's knockout and then feed the power supply wire 

through the knockout opening and into the unit junction box.

4

.  Connect the black power supply wire to the 

power outlet's

 red pigtail lead 

and the white power supply wire to the 

common 

terminal of the outlet as 

shown in 

Figures 33 and 34.

 

5

Connect the ground supply wire to the pigtail lead attached to 

outlet's green ground screw.

6

.  After the wiring is complete, replace the cover plate.

Wiring: Power Vent Termination

Alternate Instructions

 (For use when access to the termination is easy 

and a secondary electrical junction box installation is not desired). 
•  Remove the junction box cover from the termination by removing the 

attaching screw (

refer to 

Figure 30

)

.

•  Loosen the strain relief on the termination shown in 

Figure 30

.  Pull 

the pigtail in and shorten it to fit within the junction box cover.

• Route 14 gauge AWG grounded Romex wiring (not provided) from 

fireplace to the J-Box at the termination.  Ensure the wiring is safety 

plated to prevent damage by framing nails and finish drywall screws.  

Route the wire into the lower control compartment and cut to length 

before installing the terminals.  Install provided wiring hardware on the 

fireplace end of the Romex wire.

•  Refer to 

Figure 34 on Page 25

 and install the electrical hardware on 

the fireplace end of the Romex wiring.  Male terminals  (#10) on the 

Black and White wires, and ring terminals (#9) on the ground wire.  The 

termination end of the Romex will be connected to the termination with 

wire nuts (not provided).

•  Refer to 

Figure 33

 to connect the three wires of the Romex cable to 

the termination.  Ensure the ground ring terminal is grounded beneath 

a structural screw as shown.  Attach the junction box cover to the 

termination with the screw previously removed.

•  The fireplace end of the Romex will be addressed in 

Connecting The 

Power Vent To The Fireplace Control System

.

Figure 30 - Bottom of Termination

Attaching Screw

Pigtail

Junction Box Cover

Figure 33 - Junction Box Cover Removed

Ground Romex To 

The Termination

Pigtail Wires Cut 

Off And Shortened

Wire Nuts

Strain Relief Holding Romex

Figure 32 - Back Of Termination

Strain Relief

Romex Wire

6

7

Romex

Black and White

Ground Wire

Figure 31 - Romex

Содержание DRT63ST



























































Отзывы: